Search results

All mine happened before we even got there. We left 5 hours earlier than had planned to hopefully get there early & get set up before midnight. 30 minutes into the trip, the Crank Position Sensor went out & left us stranded on the side of the interstate for 4.5 hrs. Still didn't get there till...

Out the door. Be @ Crawfords in 4-5 hrs. if nothing drastic happens. Look for us in one of the small cabins. Blue '87 on 31s white '95 on 32s. Brad.

You going to the crawl? I would like to get 'em but need 'em by then. Thanx, Brad.

Ok. Found what you guys were talking about. I capped off the vac. supply. The switch has 1 wire (black w/ yellow stripe) coming out to a bullet connector that plugs into 2 wires. Do I run the wire from the Posi-Lok & put a bullet connector on it & plug it into the 2 wires? And yes it's an...

I got my Posi-Lok in today. It has a switch on it that turns on the 4wd light on the dash. Only problem is I don't know where the switch is to splice into the wires. Can anyone help? It's an '87 4.0L Aw4 231. Thanx, Brad.

Just started tearing the transmission out AGAIN!!! I pulled it the day before yesterday and installed a new flex-plate to fix the knocking sound I've been hearing. Drove it 4 miles home and lost about a quart of trans. fluid. I guess with the flex-plate being broke it let the torque converter...

I have a set of 33x12.5 boggers with 90+% tread. They have less than 1,000 road miles on them. $500. Pd $864--still have recipt. My bud has a set of 34x10.5 LTBs with about the same amount of tread & wear for $400. They measure about the same height as the boggers, but then you can say you're...

Got rocker protection & F/R lockers. Would like some sort of belly pan and a gas tank skid. Thanx, Brad.

Thanx mucho, but I don't want to be installing a locker & the Posi-Lok at the campground before I go wheeling. It's only $18 shipping for 2 lockers & the Posi-Lok & I'll have 'em Friday or Monday. I gotta get on the ball. Got to drop the transmission, replace the flex-plate. Build bumpers front...

Got any pics. of your rig handy? I'm trying to round up as much stuff by next week as possible. So far I've got Lock-right in rear, Posi-Lok in front w/ welded spiders (Rusty's has 'em on sale) & just bought some sliders from a girl in the For-Sale section. Last time I was at tellico I was in my...

I'll take whatever is left. Always need spares. I'll be at the Crawl. Blue '87--small cabin @ Crawfords Thanx, Brad.

That would probably be your best bet. Unless you want to go through Knoxville to Maryville & follow 129. There would be some back tracking though. Brad.

I'm in. I only have a 3.5" lift w/ 31s. Locked front & rear (hopefully by the crawl). My bro-in-law has a 4.5" w/ 32s locked F/R. I want to ride as much as possible but also check out the bigger trucks on the more difficult sections. We are driving there & back so I can't thrash out my ride...

Also have 4 33x12.50 Boggers. Less than 1K miles. $500 Brad.

Have 4 good 34x10.50 Swamper LTBs for sale if you might want them. $400 Brad.

Looking for anything to protect or make it go more. Also would like some upper &/or lower LCAs, 1" pucks & shackles, Posi-Lok. Live in middle TN, will be @ Cherokee Crawl, camping in Crawfords if you can deliver. E-mail pics. to [email protected] Thanx, Brad.

Me too! [email protected] Thanx, Brad

Ok. Just got back from the local trans. shop. Guy there says it sounds like the flex plate has a crack in it. Does that sound right? Anyone ever have that problem? They want $250 just to drop the trans, not counting fixing whats wrong. I've got to get this fixed, already got reservations @...

Ok, thanks for the info. I was only changing the bearings because I had the pan dropped. I went ahead and changed all the mains but left the rods in after checking each one. I did swap out one of the rod bearings with one of the new ones. I put some plasti-gauge on it and re-torqued it back...

Since I'm replacing the oil pump in my '87, I figured I'd go ahead & swap out the main & rod bearings. I ordered up a set and got started tearing down this morning. I got the main cap off & noticed that the bearing in it is labeled .010, the ones I got are standard size. I pulled a rod cap off...